40′ Sidewall (9′ High Cube) UX 2.0-Bundle

Product Overview

40′ Sidewall High Cube Flat UX 2.0 panels with studs has material to finish one side wall of an high cube container wall using the Inserts.

      • This bundle contains:
        • 4(CSW-Side Wall Insert 30 pcs.) = (60) 8′ tall sections
        •  9 (UX 2.0 (5 panels/box) = 360 Sq.Ft.
      • Part Code: SWHC40-UX


UX 2.0 Flat Panel Side Wall Bundle for a High Cube 9' high x 40' long

Bundle Description

This 40′ Sidewall bundle with material to finish one side wall of an high cube container. Suitable for interior or exterior applications. The (CWS) side wall inserts are installed on the wall first to infill the corrugation voids to prevent hidden condensation.  The embedded stud panels run horizontal, perpendicular to a shipping container corrugated rib. The goal is to provide as much contact between the studs and steel in order to maximize the holding power of the studs. This method is most often employed when the condition is less then optimal. 

    1. When weld seams are greater than or less than 44″ on center.
    2. Preferred method when modifying older containers with dings and dents

This Bundle Contains:

      • 9 Boxes (UX2.0 Flat Panel) = 360 sq-ft.
      • 4 Boxes (CSW Side Wall Inserts) = 120 pieces 48 inches long covering 480 lineal feet of corrugation in-fill or (60) 8′ tall sections
Physical Properties (CSW) Side Wall
Buy Shipping Container Insulation Panels in Bakersfield, CA

Side Wall InSerts

One box of Side Wall Inserts covers 112 Lineal feet of corrugation.


48in x 7 3/4in x 1 1/4 in


2.5 sq-ft

R-Value ASTM C518


Closed-Cell, injection-molded EPS 

ASTM C578 Type II

Canadian Standards

CAN/ULC S701 Type 2

Foam Density

1.35 lbs per cubic foot

Physical Properties (UX) 2.0 Flat Panel

2″ thick  of closed-cell, injection-molded EPS foam body achieves R-8.5 insulation The UX2.0 is our thinnest panel, optimized for flat surface interior finishing. The UX 2.0 will work on floors, walls, ceilings adapted for shipping container construction. It is a good choice as a sub-flooring base panel for shipping containers.


Panel Dimensions

24in × 48in × 2in

Horizontal Chase

48in × 1in × ¾in

Vertical Chase 24in × ¾in × ¾in


R-Value ASTM C518


ASTM C578 Type II

Closed-Cell, injection-molded EPS

Canadian Standards  CAN/ULC S701 Type 2
ASTM C303 Foam Density

1.35 lbs per cubic foot

ASTM E96 Water Vapor Permeability

 (Class III Vapor Retarder) 3.5perm/in

Maximum Service Temperature (long term)

167°F = 75 Celsius (°C)

Co-Polymer Polyproylene Insulated Stud


Interlocking Edges


Cutting Indication Lines


Code Depth Raceways


Ready for Finishing






Moisture Control 

Channels on Back only

Features Benefits
InSoFast engineered system of continuous insulation is perfectly suited for shipping container fabrication. 
  • Simple to install
    • Why work so hard?
    • Adaptable Attachment
    • No Special Tools Needed
  • Built-in Studs*
    • Engineered Framing Studs 
    • Non-conductive stud framing 
    • No energy penalty for the studs
    • Non corrosive stud…non rusting 
    • Adhesive Application no holes
  • Closed-cell high pressure fused EPS Insulation
  • Engineered for Shipping Containers
  • Lives up to its name: In So Fast

*The high-strength co-polymer plastic studs provide a positive attachment stud for finishing the container. The ribbed dovetails surface provides a cast-in-place adhesive applications against the metal surfaces. 

Insert (UX) 2.0 Flat Panel BUNDLE VIDEO

Estimating (UX) 2.0 Flat Panel Side Walls

Estimating and ordering is simple measure and add together how many high cube or standard end wall surfaces your container project requires to complete the job. Divide the total square footage (xx) by 40 sq-ft. this will determine the number of  boxes required for your project, (round up to the whole box count).  Don’t overestimate.

    • One Panel (UX2.0 Insulated Panel = (8 sq.ft)
    • One box of  5 (Insulated Panels = (40 sq.ft)
    • One box of Side Wall Inserts 15 (8′ high Corrugation infill sections)

Don’t overestimate, cut studs and inserts can be re-used.

Estimating Adhesive


New Look Buy Shipping Container Insulation Panels in Monroe, NC

Green Guard Certified Adhesive:

In Canada the Glue is LePage PL Premium

Estimating Adhesive Quantity

Estimating the amount of adhesive YOU will use has variables beyond our control like condition of your walls and how accurate are you with a glue gun? For one side wall of a 20′ standard height shipping container you will need approximately 3 tubes of the adhesive. That is in a perfect world. PL Premium 3x adhesive is applied in a ⅜” bead on the backside of the studs onto the ribbed surfaces.  We realize that a 3/8″ bead of glue is very subjective. It is important that there is enough adhesive to squish the dovetails on the back side of the stud when pressed to the container wall. Adhesive follows the “Goldie Locks rule, too much, too little, and just right To verify that enough adhesive is used, press the panel into place. Pull the panel back and check to see if the adhesive has spread out beyond the full width of the stud. It is normal for the panel to “float out” from the side of the container when it is accommodating irregularities in the container walls. Additional adhesive may be necessary in some areas. If you are doing it just right you can expect that 1 large 28-fl oz tube will cover 18 of our 24″ long studs or enough glue at a 3/8″ bead to cover 36 foot long bead of glue. 

Additionally you will have to estimate for glue around openings like windows and doors.

1 large 28-fl oz / 828 mL tube = 18 (24″ studs or inserts)

LOCTITE® PL PREMIUM® POLYURETHANE CONSTRUCTION ADHESIVE Rough estimate for  28 ounce tubes of adhesive required
Container Side Walls End Wall Ceiling  Total w/o doors and floors Floors Swing Doors Total Estimate
20′ Container – Standard 3 Per side total 6 2 1/2  6 1/2 13 7 3 23
20′ Container – High Cube 3 Per side total 7 2 1/2  6 1/2 14 7 3 24
40′ Container – Standard 6 Per side total  12 2 1/2  13 28 14 3 45
40′ Container – High Cube 6 Per side total  13 2 1/2  13 29 14 3 46

Important Notice: Container Surface Temperature Applications

When bonding EPS and XPS foam insulation, use above 40°F (4°C) and avoid cure and surface temperatures above 90°F (32°C). Surfaces must be clean, dry and free of frost, grease, dust and other contaminants. Pre-fit all materials and protect finished surfaces. If using cartridge format, cut nozzle at a 45° angle to desired bead size and puncture inner seal. Be very careful not to allow Loctite® PL® Premium to cure on a finished surface.

Cold Weather Tips:  

Interior Installation of a Shipping Container

In cold conditions below 40°F (4°C), heating the interior space of the container will not be sufficient for the adhesive to cure. The insulation panels will not allow heat to transfer to the container’s bonding surface.  It is recommended to either move the container to a heated area or tent and heat the exterior until the adhesive cures.

Exterior Installation

The interior of the container can be heated until the adhesive has cured.

Interior and Exterior Installation

Install the exterior panels first while heating the interior.  Allow adhesive to cure before installing interior insulation.

Overview / FeaturesTechnical Data / Directions

Freight Dimensions Weight
We offer free curb side deliveries on all of our orders.

You may upgrade your delivery service for an additional charge. LIFT GATE SEVICE IS AN ADDITIONAL CHARGE. Please read through our shipping and purchasing policies, for more details before placing your order. 

Product Code

Number of Parts

Box Dimension

Cubic Feet Per Box

 Weight Per Box




 CSW -Side Wall Inserts

30 pcs 4′ = 120 lnft





12 Lbs

UX2.0 5 Panels 40 SqFt 11″ 25″ 49″ 7.80 20 Lbs


5 Panels 40 SqFt





22 Lbs

Add R-Value with InSoFast PLUS

It’s easy to increase your R-Value beyond R-10 while maintaining the engineered benefits of the continuous InSoFast panels. Just start with a base of feature-rich InSoFast panels.