LowPro End Wall bundle has material to finish the end wall of a high cube or standard shipping container for interior or exterior application. The CX-LPEW studs are placed 10 inches on center alternating with the end wall inserts.
1 box kit contains 22 LowPro End Wall Studs and 9 End Wall Inserts Bundle
CX-LPEW: LowPro End Wall bundle is part of a assembly that has material to finish the end wall of a 9′ high cube or 8′ standard shipping container. The LP-EW studs are placed 10 inches on center alternating with the end wall inserts. The LP-EW studs are ideally suited for container conversions for commercial, residential, industrial, interior or exterior applications where thin wall insulation and framing is the primary concern. Refer to the container diagram to determine the proper fit is very important.
*This LP-EW bundle is a 3 part assembly designed to work on the end wall of a container. Sheet infill insulation supplied by others.
SKU: CX-LPEW
![]() |
|||||
LP-EW LowPro Insulated Stud One box of the LP-EW 22 Insulated studs will do 44 lineal feet of framing. |
|||||
LowPro-Insulated Stud Endwall Architectural Dimensions |
|
||||
Dimensions |
5 1/2in × 24in × 2 1/2 in |
||||
Coverage |
1.00 sq-ft |
||||
R-Value ASTM C518 |
R-10.5 |
||||
ASTM C578 Type II |
Closed-Cell, injection-molded EPS |
||||
Canadian Standards CAN/ULC S701 Type 2 |
|||||
ASTM C303 Foam Density |
1.35 lbs per cubic foot |
||||
ASTM E96 Water Vapor Permeability |
(Class III Vapor Retarder) 3.5perm/in |
||||
Maximum Service Temperature (long term) |
167°F = 75 Celsius (°C) |
||||
Surface |
|||||
Interlocking Edges |
√ |
||||
Engineered for Shipping Containers |
√ |
||||
Exterior Application |
√ |
||||
Interiors Application |
√ |
![]() |
|
Endwall Inserts End Wall Inserts or the container’s nose corrugation. One box of Inserts covers the end wall. |
|
Endwall Insert Architectural Dimensions | jpg |
Insert Dimensions | zip file |
See Diagram | 5 1/4 in × 48in × 1 5/8 in |
Coverage per pcs | 1.75 sq-ft |
One Box -20 inserts 4′ long | (covers 35’ Sq-ft) |
Interior side of the end wall | 1 boxes |
Exterior side of a the end wall | 1 boxes |
R-Value ASTM C518 | R-4 per in |
ASTM C578 Type II |
Closed-Cell, injection-molded EPS |
Canadian Standard CAN/ULC S701 Type 2 | |
Foam Density | 1 lbs per cubic foot |
Interiors | √ |
Exteriors | √ |
Shipping Containers | √ |
*The high-strength co-polymer plastic studs on variable 11 – 22 inches on centers provide a positive attachment stud for finishing the container. The ribbed dovetails surface provides a cast-in-place adhesive applications against the metal surfaces.
Estimating and ordering is simple measure and add together how many square feet of end wall framing that your container requires to complete the job. This is easy to determine the number of boxes needed, it is 1 box per side you wish to insulate. Don’t overestimate, cut studs, panels and inserts can be re-used.
POLYURETHANE CONSTRUCTION ADHESIVE
![]() |
![]() |
Estimating the amount of adhesive YOU will use has variables beyond our control like condition of your walls and how accurate are you with a glue gun? The example below is for one side wall of a 20′ standard height shipping container you will need approximately 3 tubes of the adhesive. That is in a perfect world. PL Premium 3x adhesive is applied in a ⅜” bead on the backside of the studs onto the ribbed surfaces. We realize that a 3/8″ bead of glue is very subjective. It is important that there is enough adhesive to squish the dovetails on the back side of the stud when pressed to the container wall. Adhesive follows the “Goldie Locks rule, too much, too little, and just right To verify that enough adhesive is used, press the panel into place. Pull the panel back and check to see if the adhesive has spread out beyond the full width of the stud. It is normal for the panel to “float out” from the side of the container when it is accommodating irregularities in the container walls. Additional adhesive may be necessary in some areas. If you are doing it just right you can expect that 1 large 28-fl oz tube will cover 18 of our 24″ long studs or enough glue at a 3/8″ bead to cover 36 foot long bead of glue.
Additionally you will have to estimate for glue around openings like windows and doors.
1 large 28-fl oz. / 828 mL tube = 18 (24″ studs or inserts)
POLYURETHANE CONSTRUCTION ADHESIVE Rough estimate for 28 ounce tubes of adhesive required |
|||||||
Container | Side Wall | End Wall | Ceiling | Total Walls & Ceiling | Floors | Swing Doors | Total Estimate |
20′- Standard | 3 | 2 1/2 | 6 1/2 | 13 | 1 1/2 | 3 | 18 |
20′- High Cube | 3 | 2 1/2 | 6 1/2 | 14 | 1 1/2 | 3 | 19 |
40′- Standard | 6 | 2 1/2 | 13 | 28 | 3 | 3 | 34 |
40′- High Cube | 6 | 2 1/2 | 13 | 29 | 3 | 3 | 34 |
When bonding EPS and XPS foam insulation, use above 40°F (4°C) and avoid cure and surface temperatures above 90°F (32°C). Surfaces must be clean, dry and free of frost, grease, dust and other contaminants. Pre-fit all materials and protect finished surfaces. If using cartridge format, cut nozzle at a 45° angle to desired bead size and puncture inner seal. Be very careful not to allow Loctite® PL® Premium to cure on a finished surface.
Please read all the current Shipping, Purchasing & Returns *
Product Code |
Number of Parts |
Box Dimension |
Cubic Feet Per Box |
Weight Per Box |
||
Length |
Width |
Height |
||||
CX-LPEW |
LP-EW 22 pcs. End Wall Inserts 9 pcs. |
16″ | 16″ | 49″ | 7.26 | 18 Lbs |
It’s easy to increase your R-Value beyond R-10 while maintaining the engineered benefits of the continuous InSoFast panels. Just start with a base of feature-rich InSoFast panels.