Corner Post Insert is a 3 part per section assembly designed to work on the inside corner post end wall of a standard container.
End Wall Corner Inserts contains:
Box contains 8 foam inside corner posts insert and 4 metal utility corner attachment studs
(I-EWCP-ST) is part of a assembly that has material to finish the inside corners of the end wall of a standard shipping container. The corner post inserts infill the corner’s corrugated voids preventing hidden condensation. The Metal “M” angle provides a solid corner stud for finishes like drywall.
(I-EWCP-ST) = 8 pcs foam inserts and 4 metal “M” corner studs, each End Wall Corner section is a 3 part assembly designed to work on the inside corner end wall of a container.
(I-EWCK) = 1 End Wall Corner Inserts – interior application
End Wall corner Inserts or the container’s nose corrugation. One box of Inserts covers the end wall.
|Dimensions||5 1/4 in × 45 1/4in × 1 5/8 in|
|Coverage per boxed unit||One Set of inside corners|
|One Box – 8 pcs foam inserts||(covers inside corners)|
|Interior side of exposed foam the end wall||2 in thick|
|Inside Metal Corner||(covers inside corners)|
|Inside fastening width and length||1 3/4 in x 1 3/4in x 45 1/4in|
|R-Value ASTM C518||R-4.5 per in
|ASTM C578 Type II||
Closed-Cell, injection-molded EPS
|Canadian Standard CAN/ULC S701 Type 2|
|Foam Density||1.5 lbs per cubic foot|
(I-EWCI) = 1 End Wall Corner Inserts – interior application
InSoFast engineered system of continuous insulation perfectly suited for shipping container fabrication for the End Wall inside Corner Inserts
Estimating and ordering is simple add together how many interior end walls, (the “nose” of the container) your container project needs. It is simple to determine the number of boxes needed, it is 1 box per (the “nose” of the container) . (I-EWCP) = 1 End Wall Corner Inserts for each container end wall. Don’t overestimate.
Estimating the amount of adhesive YOU will use has variables beyond our control like condition of your walls and how accurate are you with a glue gun? The example below is for one side wall of a 20′ standard height shipping container you will need approximately 3 tubes of the adhesive. That is in a perfect world. PL Premium 3x adhesive is applied in a ⅜” bead on the backside of the studs onto the ribbed surfaces. We realize that a 3/8″ bead of glue is very subjective. It is important that there is enough adhesive to squish the dovetails on the back side of the stud when pressed to the container wall. Adhesive follows the “Goldie Locks rule, too much, too little, and just right To verify that enough adhesive is used, press the panel into place. Pull the panel back and check to see if the adhesive has spread out beyond the full width of the stud. It is normal for the panel to “float out” from the side of the container when it is accommodating irregularities in the container walls. Additional adhesive may be necessary in some areas. If you are doing it just right you can expect that 1 large 28-fl oz tube will cover 18 of our 24″ long studs or enough glue at a 3/8″ bead to cover 36 foot long bead of glue.
Additionally you will have to estimate for glue around openings like windows and doors.
1 large 28-fl oz. / 828 mL tube = 18 (24″ studs or inserts)
Rough estimate for 28 ounce tubes of adhesive required
|Container||Side Wall||End Wall||Ceiling||Total Walls & Ceiling||Floors||Swing Doors||Total Estimate|
|20′- Standard||3||2 1/2||6 1/2||13||1 1/2||3||18|
|20′- High Cube||3||2 1/2||6 1/2||14||1 1/2||3||19|
|40′- Standard||6||2 1/2||13||28||3||3||34|
|40′- High Cube||6||2 1/2||13||29||3||3||34|
When bonding EPS and XPS foam insulation, use above 40°F (4°C) and avoid cure and surface temperatures above 90°F (32°C). Surfaces must be clean, dry and free of frost, grease, dust and other contaminants. Pre-fit all materials and protect finished surfaces. If using cartridge format, cut nozzle at a 45° angle to desired bead size and puncture inner seal. Be very careful not to allow Loctite® PL® Premium to cure on a finished surface.
Please read all the current Shipping, Purchasing & Returns *
Number of Parts
Cubic Feet Per Box
Weight Per Box
End Wall Corner Inserts 12 pcs.
It’s easy to increase your R-Value beyond R-10 while maintaining the engineered benefits of the continuous InSoFast panels. Just start with a base of feature-rich InSoFast panels.