LowPro Insulated corrugation infill framing is part of an assembly to finish shipping container walls using the CX-LowPro infill framing and side wall inserts.
1 Box contains 15 LowPro Studs =30 ln-ft. of infill framing (7 1/2) 8' Sections)
This CX LowPro is an assembly of insulated infill framing for container side walls. The infill framing is typically placed on either 11 – 22 inches on center in an alternating pattern with the side wall inserts. The CX-LP infill framing is ideally suited for container conversions in commercial, residential, industrial, interior or exterior applications where thin wall insulation and framing is the primary concern.
This CX LowPro bundle is a 3 part assembly for the long side walls of a container. Stock sheet infill insulation is supplied by others.
![]() |
|
CX-LP LowPro Insulated Stud |
|
Dimensions |
7 1/2in × 24in × 2in |
Coverage |
1.25 sq-ft |
R-Value ASTM C518 |
R-8.5 |
ASTM C578 Type II |
Closed-Cell, injection-molded EPS |
Canadian Standards CAN/ULC S701 Type 2 |
|
ASTM C303 Foam Density |
1.35 lbs per cubic foot |
ASTM E96 Water Vapor Permeability |
(Class III Vapor Retarder) 3.5perm/in |
Maximum Service Temperature (long term) |
167°F = 75 Celsius (°C) |
Surface |
|
Interlocking Edges |
√ |
Engineered for Shipping Containers |
√ |
Exterior Application |
√ |
Interiors Application |
√ |
*The high-strength co-polymer plastic studs on 22-inches centers provide a positive attachment stud for finishing the container. The ribbed dovetails surface provides a cast-in-place adhesive applications against the metal surfaces.
Estimating and ordering is simple measure and add together how many lineal feet of the corrugation infill framing that your container requires to complete the job. Divide the total lineal footage by the 2′ long inserts to find out how many CX-LP you require. Don’t overestimate, cut studs, panels and inserts can be re-used.
Infill framing is typically set at 22 inches on center. One side of a 20′ standard container would need 10 – 11 insulated framing sections depending on your specific layout.
LOCTITE® PL PREMIUM® POLYURETHANE CONSTRUCTION ADHESIVE
![]() |
![]() |
Estimating the amount of adhesive YOU will use has variables beyond our control like condition of your walls and how accurate are you with a glue gun? The example below is for one side wall of a 20′ standard height shipping container you will need approximately 3 tubes of the adhesive. That is in a perfect world. PL Premium 3x adhesive is applied in a ⅜” bead on the backside of the studs onto the ribbed surfaces. We realize that a 3/8″ bead of glue is very subjective. It is important that there is enough adhesive to squish the dovetails on the back side of the stud when pressed to the container wall. Adhesive follows the “Goldie Locks rule, too much, too little, and just right To verify that enough adhesive is used, press the panel into place. Pull the panel back and check to see if the adhesive has spread out beyond the full width of the stud. It is normal for the panel to “float out” from the side of the container when it is accommodating irregularities in the container walls. Additional adhesive may be necessary in some areas. If you are doing it just right you can expect that 1 large 28-fl oz tube will cover 18 of our 24″ long studs or enough glue at a 3/8″ bead to cover 36 foot long bead of glue.
Additionally you will have to estimate for glue around openings like windows and doors.
1 large 28-fl oz / 828 mL tube = 18 (24″ studs or inserts)
LOCTITE® PL PREMIUM® POLYURETHANE CONSTRUCTION ADHESIVE Rough estimate for 28 ounce tubes of adhesive required | |||||||
Container | Side Walls | End Wall | Ceiling | Total w/o doors and floors | Floors | Swing Doors | Total Estimate |
20′ Container – Standard | 3 Per side total 6 | 2 1/2 | 6 1/2 | 13 | 7 | 3 | 23 |
20′ Container – High Cube | 3 Per side total 7 | 2 1/2 | 6 1/2 | 14 | 7 | 3 | 24 |
40′ Container – Standard | 6 Per side total 12 | 2 1/2 | 13 | 28 | 14 | 3 | 45 |
40′ Container – High Cube | 6 Per side total 13 | 2 1/2 | 13 | 29 | 14 | 3 | 46 |
When bonding EPS and XPS foam insulation, use above 40°F (4°C) and avoid cure and surface temperatures above 90°F (32°C). Surfaces must be clean, dry and free of frost, grease, dust and other contaminants. Pre-fit all materials and protect finished surfaces. If using cartridge format, cut nozzle at a 45° angle to desired bead size and puncture inner seal. Be very careful not to allow Loctite® PL® Premium to cure on a finished surface.
In cold conditions below 40°F (4°C), heating the interior space of the container will not be sufficient for the adhesive to cure. The insulation panels will not allow heat to transfer to the container’s bonding surface. It is recommended to either move the container to a heated area or tent and heat the exterior until the adhesive cures.
The interior of the container can be heated until the adhesive has cured.
Install the exterior panels first while heating the interior. Allow adhesive to cure before installing interior insulation.
Yes but act quickly. To cancel or modify your order contact us immediately at orders@insofast.com or call 888-501-7899 with your request. However, we cannot guarantee that your request to modify or cancel your order will be granted.
You can cancel your order any time before it reaches the “In Process Ready to Ship” stage. Once your order is in processed and sent to the fulfillment center, it cannot be cancelled without a processing fee. We strive to have all orders “In Process Ready to Ship” within 24 hours. You have less than 24 hours to cancel your order without any additional fees. If it is past the 24-hour mark and you do not want the items you ordered, you can still return them. See below.
Yes you will be charged in the event of a cancellation. The freight company’s charges for delivery will be assessed. At a minimum you will be charged a $30 restocking fee per box and up to 50% of the cost of the entire order.
Authorized Returns are subject to $35 Restocking Charge per box and up to 50% of the cost of the whole order. No Returns after 30 days. No returns from authorized retailer will be accepted, all returns must go through the authorized retailer. Only unopened and unused boxes will be considered for return. No Returns for sales outside the continental US
No credits will be issued until the product has been returned and evaluated for condition.
Please read all the current Shipping, Purchasing & Returns *
You may upgrade your delivery service for an additional charge. LIFT GATE SEVICE IS AN ADDITIONAL CHARGE. Please read through our shipping and purchasing policies, for more details before placing your order.
Product Code |
Number of Parts |
Per Box Dimension |
Cubic Feet Per Box |
Weight Per Box |
||
Length |
Width |
Height |
||||
CX -LPSW-PB |
15 pcs = 30 lnft |
20″ |
26″ |
12″ |
3.61 |
9 Lbs |
It’s easy to increase your R-Value beyond R-10 while maintaining the engineered benefits of the continuous InSoFast panels. Just start with a base of feature-rich InSoFast panels.